Understanding your Edison/Explorer Board rig¶
Getting Physical: Build your rig/put the physical pieces together¶
The Explorer board is where all the communications are housed for the rig, as well as the battery charger. The Edison is the mini-computer where all the OpenAPS code will be sent and used. In order for this to work, first you have to screw and connect the Edison and Explorer Board together with the nuts and bolts you order.
The nuts and bolts are tiny, and the spaces are a little tight. It really helps to use a set of tweezers and a small Phillips head screwdriver.
It’s easiest to start with the Explorer board and put on 2 nuts and gold screws (nuts on the side with most of the wiring) inside the little outline where the Edison will eventually sit. Gold screws should be placed as shown, with nuts on the backside. Then, lay the Edison board on top, aligning the screw holes. Use a small Phillips head screwdriver to tighten the screws into the gold screws beneath them. The Edison board should not wobble, and should feel secure when you are done. Attach your battery into the explorer board plug. A single red light should appear and stay lit. During the course of your OpenAPS rig use, it’s good practice to periodically check that the nuts and screws stay tightened. If they come loose, the Edison can wobble off the connection to the Explorer board and you will either get looping failures (if it’s loose) or be unable to connect to the Edison (if it comes completely off).
Charging Lipo Battery¶
You can use the little white block that comes with an iPhone (or similar charger) and a microB-USB cable. The same cables you used to setup the rig and connect to the computer will work for charging, too. Either one of the USB ports on the explorer board will work for charging. When charging is active, there is an extra red light on in the corner of the Explorer board. When charging is complete, that corner red light will turn off. It may come back on periodically as the battery “tops off”. You won’t do any damage leaving the rig plugged in for longer than the charge takes.
While the rig is plugged in for charging, the Nightscout battery pill will read approximately 65%. This is because it is reading the charging voltage rather than the battery voltage. Once you disconnect from the charger, the Nightscout battery pill will display the lipo battery’s voltage and percent again.
What the lights mean and where they are¶
- The LED between the two ports is the power. If this light is on, your rig is on.
- The LED in the corner is the charging indictator.
- The two next to the microUSBs (one green on the latest boards) are for the cc1110 radio chip. By default they just blink once each when you mmtune or otherwise reset it.
Where is the radio?¶
The radio and antenna are down on the end of the board where you see a little white stick. (Opposite end of the board from where your battery connects at the JST connector).
Cutting the trace to improve radio communication¶
Some OpenAPS users have found that cutting a portion of the Explorer Board’s hidden copper antenna wire (called a trace) will improve radio comms with the pump. Before doing this, remember to disconnect any attached battery or power source first. For North American (NA) pumps (using the 916MHz band), you’re looking to cut near that white line that is between the 1 and the 5 in the “915.” Consider cutting on the 1-side rather than the exact spot where the white “cut” line is drawn because it is so close to the corner where the rest of the copper wire goes. To make the cut, use a sharp x-acto blade to cut through the copper just beneath the green surface of board. It will take a few swipes and you’ll hear a small scraping noise when you get through the wire. Make sure you’ve cut all the way through the wire to the green circuit board material on the other side.
Watch this video for an example: https://www.facebook.com/groups/TheLoopedGroup/permalink/1854229718127019/?hc_location=ufi
Lipo batteries are great for a lot of things…but taking damage is not one of them. Please treat lipo batteries with care. Keep them protected from puncture. The explorer board has some “pointy” parts on the underside, so providing some protection from the board’s squish is a good idea. A small piece of protection (such as a business card or non-conductive thin foam sheet) will help protect the battery from the board above it.
Since there is some warmth with an OpenAPS rig, it is also not recommended to put a rig unprotected in a pocket close to the body. The lipo battery can become warped from the heat or bent from being in the pocket and potentially compromised. A durable case or waist-belt pouch is a good idea (see here for both hard and soft case ideas).
There are several places to get lipo batteries, with lots of different dimensions and capacities. A 2000 mAh lipo will get you about 12-14 hours of use, assuming you have the standard setup (which is what you get following these docs) running.
What happens if you have multiple rigs?¶
If you have multiple OpenAPS rigs, they’re built to be polite to each other - so even if you had 2+ rigs in same room, they won’t trip each other up. They “wait for silence” before issuing any commands to the pump. By having multiple rigs throughout a house, you can move from room-to-room without carrying rigs because the rigs will pass-off comms as you moves in and out of the rig’s range. While stationary rigs will not need lipo batteries and can be plugged directly into the wall from the explorer board, you may still want to consider hooking up a battery so that the rig can quickly be taken with you on the go if needed and should the power fail you can still stay looping.